top of page

General information

•4 levels of water level checking, viz. 1/4th, half, 3/4thand full

•Receiver has 30Amps potential free contact relay

•Do not directly couple a motor to the receiver relay(always use external relay to trigger)

•Signal range 3 – 4 kms (line of sight)Conditions for pump ON/OFF

•When overhead tank water level is 1/4thor below => pumpON

•When overhead tank water level is FULL or more => pumpOFFFlow of waterFloat sensors

 

Model: FBXPC03A water level sensor + transmitter1 output signal lineLoop back to 4 input signal lines Each connected to float switches or equivalent Indicators Wireless automatic water level controller

•Power: GREEN

•Sync: BLUE

•1/4thwater level: RED

•Half water level: RED

•3/4thwater level: RED

•Full water level: REDTechnical details:

•Transmitter with external PA +28dbm

•Operating frequency: 380 – 480 MHz

•System operates works on signal hop mechanism. Sig

naltransmission happens at more than 12-15 predefined

frequencies

•Modulation type: GFSK

•Radio IC: CC1100 (Chipcon/TI) and other equivalents in sub-GHz freq.

•Modulation: GFSK

•Data packet error correction mechanism: FEC Connection wiring diagram:

Level sensor unit has a 6 point connector, of which2 are for power supply and the remaining 4 are for signal level checking.The main signals loops back through a level sensor/ float sensor(potential free contacts) to the respective level inputs. The red

line shown in the picture contains the pulsating current of veryfeeble strength.

Operating voltage:110-220VAC/50-60Hz to 12VDC converter adapter supplied.

Unit can also be plugged to any 12V external battery. Active working hours depends on the battery power.

Application and features:

  • Turning motor pump ON/OFF from a distant location
  • Automation / manual mode of operation
  • Automatic mode: Remote controller used to turn ON/OFF
  • Manual mode: Existing pump starter used to turn ON/OFF
  • (In manual mode, remote controller signals are bypassed)

 

Model: FBXPC03A receiver with automatic ON/OFF switch2 output terminal through 30Amps potential free contact Manual switch to bypass the wireless signal from the

transmitter Indicators Wireless automatic water level controller

•Power: GREEN

•Sync: BLUE

•Mode: YELLOW: manual / radio

Tank level indicators

•1/4th water level: RED

•Half water level: RED

•3/4th water level: RED

•Full water level: RED Technical details:

•Operating frequency: 380 – 480 MHz

•Receiver operates works on signal hop mechanism. R

eception happens at more than 12-15 predefined frequencies

•Modulation type: GFSK

•Radio IC: CC1100 (Chipcon/TI) and other equivalents in sub-GHz freq.

•Receiver sensitivity: – 112 dbm

•Modulation: GFSK

•Data packet error correction mechanism: FEC

•1m wire / rubber duck antenna (+3dbi) Precautions and mounting locations:

•Avoid connecting relay contactor directly to motors (initial startup

surge currents will damage the device)

•Mounted on the top of wall

•Easy mounting with 4 screws to secure it tightly

•IP65 enclosure unit, robust and weatherproof

•Suitable for out door applications as well

•Keep away antennas from external metallic enclosures

Operating voltage:110-220VAC/50-60Hz to 12VDC converter adapter supplied.Unit can also be plugged to any 12V external battery. Active working hours depends on the battery power.

Application and features:

  • Turning motor pump ON/OFF from a distant location
  • Automation / manual mode of operation
  • Automatic mode: Remote controller used to turn ON/OFF
  • Manual mode: Existing pump starter used to turn ON/OFF
  • (In manual mode, remote controller signals are bypassed)

 

Transmitter unit:

Enclosure type: IP 65 (color grey)

Size: 190 x 90 x 55 mm

Weight: 350gms

Metallic enclosure dimension:300 x 300 x 170 mm

Weight: 4500 gms

 

Receiver unit:

Enclosure type: IP 65 (color grey)

Size: 190 x 90 x 55 mm

Weight: 350gms

Metallic enclosure dimension:300 x 300 x 170 mm

Weight: 4500 gms

Wireless Automatic Water Level Controller

₹1.00Price
Excluding Tax
    bottom of page